My Account  Cart Contents  Checkout  
  Top » Catalog » Modders Shoppe » Electronics-Converters » Converter Boards » ShkBck1A Log In |  Cart Contents  |  Checkout | 
Categories
Completed Assemblies->
Fixed Lighting->
Modders Shoppe->

View All Products ->

All Products sorted by Categories ->

All Products sorted by Manufacturers ->
Search
 
Use keywords to find the product you are looking for.
Specials more

Super MJ LED (4-die) - Uncut 5-pack
 $22.00  $19.80 

FF 2-level switch-16 ohm
 $10.00  $8.50 

Aleph A19 UV Head with a Downboy LE (Black)
 $150.00  $130.00 
Fraen LP
Fraen LP
 $2.00  $2.00 
Fraen LP-FF
Fraen LP-FF
 $8.00  $6.00 
Super MJ LED (4-die) - Uncut
Super MJ LED (4-die) - Uncut
 $4.50  $4.05 

Tank Night Light Story
 $0.00  $0.00 
Firefly CR2 power pack (premium)
Firefly CR2 power pack (premium)
 $36.00  $30.60 
Cyan Lambertian (HD)Star LXHL-ME1D Bin Q4JC **lower price
Cyan Lambertian (HD)Star LXHL-ME1D Bin Q4JC **lower price
 $6.50  $5.53 

Aleph A19 UV Head with a Downboy LE (Natural)
 $150.00  $130.00 
Latest Products more

Cree on Board (UV) - panel of 36
 $500.00 
Control Scan
Increase Sales with Verified Secure Seal from Control Scan!

SHARK Buck 1A

 [ShkBck1A]
 $26.00 - $27.00 

Description

SHARK Buck 1A

Shark Buck a step down converter. The Shark Buck is the same diameter (0.75") as the Shark and Blue Shark.

It has the same trim pot and trim pot functionality.  Remora can be mounted on the Shark Buck and behaves the same as the regular Shark.  It will be a little taller.

The Shark Buck has reverse battery protection and accommodates the same copper C as on the regular Shark for optimum thermal transfer to the heat sink.

There are two sense resistors on this board making it easier to generate a valid output current combination.

One 0.1 ohm resistor = 1A max. (default)
Two 0.1 ohm resistors or one 0.05 ohm resistor= 2A max.
One 0.1 ohm + one 0.05 ohm = 3A max. (maximum output configuration)

- Minimum input voltage 3V. (Recommended to stay above 4V)
- Absolute Maximum Input Voltage: 25 (Recommend max 24V) on fresh batteries

To determine a different configuration determine the following:

1) sum up the Vf of all the series LEDs.

2) Based on the battery technology and number of batteries determine the low and high battery voltage.

3) For a boost the low and high must be less than the sum of Vf. For a buck the low and high must always be higher than the sum of Vfs.

Requires heatsinking 

To thermally bond Blue Shark or Shark Buck to a heat sink, use a super thin (paper thin or thinner) layer of thermal glue.

When mounting a Blue Shark, Shark Buck etc to the heat sink use an ultra-thin layer of adhesive for maximum conductivity.  Too thick of a layer is like creating an air gap.

For proper mounting the converter board should be clamped.  Thermal interface to heat sink must be less than 15C/W.

Arctic Alumina Thermal Adhesive (2 Part Epoxy)
Arctic SILVER Thermal Adhesive 7g set
Arctic Alumina Thermal Adhesive (2 Part Epoxy) Medium Cure

Shark Buck Thread on Sandwich Shoppe Forum

These are a few Q & As but not all.  Please read the thread.

The trim pot can be removed and an external 20K pot can be hooked up allowing control of the
converter board. The trim pot input can also be PWM controlled via a microprocessor.

Generic Specs  Post #24

External rotary switch Post #62

External pot  Post # 116 and wiirng #121

Q:  Does the Shark Buck run OK on one cell?  I want to run an SST-50 with 2amps or better on a single 18650.

A:  No, the Shark Buck needs a couple of volts overhead to maintain regulation. With a large LED or multiple parallel LEDs with Vf of 3.5V or so requires 5+ volts for the Shark Buck. That would be min or the voltage of the discharge state of the batteries and a fresh cell setup would therefore be 6-8V.

Q:  Question regarding minimum voltage input.

A:  For a specific application you must always have Vin greater than Vf or the Buck converter will not be stepping down. If the P7 Vf is 3.5V then Vin must always be greater than 3.5V for A buck converter.

The buck regulator will fall out of regulation when Vin approaches ~20% over Vf or ~1.3V above 3.5V.

For a 4 cell NiMH, Alkaline means you will maintain regulation for only a short period of time on high. After that it will fall into DD mode.

The batteries under load will sag making Vin lower on high.

Q:  Can I drive 3 Cree XM-L or similar on 3X 17670 Li-Ion's 

A:  Three LEDs with Vf of 3V is 9V in total.

Remember take your batteries low and high Voltage. For a fresh li-ion that would be 4.2V and I don't know where you consider discharge is, but, let's say 2.5V.

For three batteries that would be 7.5V to 12.6V.

In order for the Shark buck to be in regulation all the time the complete battery range must be higher with margin in order to maintain regulation.

Since 9V is not always less than 7.5V - 12.6V this situation is not optimum for full regulation all the time.

It may be in regulation under fresh batteries conditions, but, will fall out of regulation at some point in time before the batteries are fully depleted.

To determine a different configuration determine the following:

1) sum up the Vf of all the series LEDs.

2) Based on the battery technology and number of batteries determine the low and high battery voltage.

3) For a boost the low and high must be less than the sum of Vf. For a buck the low and high must always be higher than the sum of Vfs.


Good for running one or more high power LED in a step-down configuration.

 

Shark Buck test procedure?

 

Available Options:
Remove trimpot:

Images

SHARK Buck 1A SHARK Buck 1A

Mfg Info

Manufacturer Info
Other products

Extra Info

Comments
There are currently no product reviews
Write a review on this product!


Extra Info
This product was added to our catalog on Sunday 02 November, 2008.
Notify me of updates to SHARK Buck 1A
Tell someone you know about this product.


Quantity Price Chart
Base $27.00
2 - 10 $27.00
11 - 20 $27.00
21 - 30 $27.00
31 - 40 $27.00
41 - 49 $27.00
50 - 60 $26.00
61 - 70 $26.00
71 - Above $26.00
Add to Wish List
 $26.00 - $27.00  Quantity:     
Customers who bought this product also purchased
Information
Contact Us->
Information Pages
Shipping
Shopping Cart more
0 items
Your Account
Your Email Address
Your Password
Best Sellers
01.Kroll Tailcap Switch (New and improved)
02.Fraen LP
03.EP O-Ring 18
04.Silicon 15 O-ring for Aleph Power pack
05.Sandwich Retaining Oring
06.Silicon 16 O-ring for PD
07.Retaining ring
08.O-ring-FF Better Fit 15
09.Arc Threaded Ring (limit 2 per person)
10.ECan EN Plated

Copyright © 2017 Chain Reaction Ecommerce, Inc. Powered by CRE Loaded
Using CRE Loaded PCI B2B v6.4.1