My Account  Cart Contents  Checkout  
  Top » Catalog » YC » GDuP-HO Log In |  Cart Contents  |  Checkout | 
Categories
Completed Assemblies->
Fixed Lighting->
Modders Shoppe->
Non-Custom Lights & Stuff
Office Supplies
Sandwich Shoppe Gift Certificate
Soldering Equipment
Test Equipment
Drop-In Sandwiches - Discontinued

View All Products ->

All Products sorted by Categories ->

All Products sorted by Manufacturers ->
Search
 
Use keywords to find the product you are looking for.
Specials more

Aleph A19 UV Head with a Downboy LE (Natural)
 $150.00  $130.00 

Aleph A19 UV Head with a Downboy LE (Black)
 $150.00  $130.00 
Universal Heat Sink
Universal Heat Sink
 $20.00  $16.00 
CreeBar
CreeBar
 $36.00  $35.00 
McClicky2 Switch (Aleph and McClickie pak)
McClicky2 Switch (Aleph and McClickie pak)
 $7.50  $7.00 
Firefly CR2 power pack (premium)
Firefly CR2 power pack (premium)
 $36.00  $28.80 

McR-10 Rebel
 $14.00  $11.20 
McGizmo Ti 32 SR Split Ring
McGizmo Ti 32 SR Split Ring
 $6.00  $4.80 

Krazy K2 Sale UYAN
 $4.00  $3.50 

McR-12 Rebel
 $13.00  $10.40 
Control Scan
Increase Sales with Verified Secure Seal from Control Scan!

GDuP Boost/Buck Converter HIGH output(3-level driver) 20% off

 [GDuP-HO]
 $40.00 - $42.00 

Description

GDuP Boost/Buck Converter HIGH output(3-level driver) 20% off

GDuP is a Microprocessor based fully-regulated boost/buck converter.  This is the high output version GDuP which has a resistor change giving it a broader range. 10mA-1200mA

The GDuP is based on the GD driver and is a true buck/boost converter. It will run from 1.8V to 5V safely. So, yes to two cell Alkaline, NiMH or even three cell Alkaline/NiMH.   Single 123, lithium battery.

Capable of stepping through three levels of brightness.

Default Levels are set at 20mA, 180mA and 1200mA

Click through the 3 levels and release after the blip to set.

The GDuP turns your single stage light into a three stage clicky or twisty.

Has the capability of retaining your last entered state.

Comes with bare anode contact board and one two pin connector. (only the GND connector pin mates with the anode board)

Board bare pcb thickness: ~0.9mm

Note:  If the GDuP converter is custom programmed and is successful, it is not tested again.

The GDuP has self calibration mode.

 

If you want it functionally tested it will cost $14.00 for each converter because wires need to be added and test performed. 

 

------------------------------

Tallest component top side: 3mm

Tallest component bottomside: 1mm

Total thickness ~4.9mm (0.193")

Board diameter: 0.55" (14mm)

The board runs best when used in a single cell application (CR123, RCR123 or 2,3 alkaline batteries).

Do not use this board in any two 123 cell configurations as this will fry the components on the board.

Board has components on both sides (bottomside not shown).

Extreme care must be taken when soldering this board to other components as too much heat and components will fall off either the top side or bottomside depending on which way gravity is pulling.

Custom versions of the UI can be made. Inquire for more info.

 See CPF thread here for more info.

NEW:  Change the 3 levels by choosing the yes option and typing in the desired levels in mA: ie.  50 200 1000

Range is 10mA -1200mA (GDuP High Output version)

Make sure you are logged in for your options to show  up on the order.

We tested this.  If you go to check out and you have not put in your name, address etc the options are not retained.

Please re-input your item and options.  The options will show up on your order as you go through check out.

 

How GDuP Auto-cal works:

 
When you turn the light on it will determine in 1 second if the current level is within specifications.  If it is not within specifications it will blip quickly once a 1 second.   This is the indicator it not calibrated.  It will automatically start a re-cal procedure and if successful ( a few seconds to many seconds later) it will blip quickly twice.  Once it blips twice it signifies it cal'd correctly and stored it away.

You can now cycle to the next level and wait to see if it auto-cals or not. You need to do this once and it will do this periodically with LED aging.

But, it's automatic.  Just use the light.  It should be correct after a few usages.

The full description is on the GDuP thread on CPF.

Available Options:
Write in levels:
Function Test:
Change levels on GDuP:

Images

GDuP Boost/Buck Converter HIGH output(3-level driver) 20% off GDuP Boost/Buck Converter HIGH output(3-level driver) 20% off GDuP Boost/Buck Converter HIGH output(3-level driver) 20% off

Mfg Info

Manufacturer Info
Other products

Extra Info

Comments
There are currently no product reviews
Write a review on this product!


Extra Info
This product was added to our catalog on Wednesday 19 May, 2010.
Notify me of updates to GDuP Boost/Buck Converter HIGH output(3-level driver) 20% off
Tell someone you know about this product.


Quantity Price Chart
Base $42.00
2 - 10 $42.00
11 - 20 $41.00
21 - 30 $40.00
31 - 40 $40.00
41 - 50 $40.00
51 - 60 $40.00
61 - 70 $40.00
71 - Above $40.00
Add to Wish List
 $40.00 - $42.00  Quantity:     
Customers who bought this product also purchased
Information
Contact Us->
Information Pages
Shipping
Shopping Cart more
0 items
Your Account
Your Email Address
Your Password
Best Sellers
01.Fraen LP
02.Connector and Bare Emitter Board
03.EP O-Ring 18
04.McR-20
05.Makita Dock 2 Black (14V & 18V)
06.20mm IMS Reflector
07.Madmax Plus Step Up Converter Board-Wide Open
08.White Luxeon III 3W Star (LXHL-LW3C) TV1J
09.Sandwich Retaining Oring #12
10.McR-20 Seoul

Copyright © 2024 Chain Reaction Ecommerce, Inc. Powered by CRE Loaded
Using CRE Loaded PCI B2B v6.4.1