My Account  Cart Contents  Checkout  
  Top » Catalog » Modders Shoppe » Electronics-Converters » Converter Boards » GDuP-HO Log In |  Cart Contents  |  Checkout | 
Completed Assemblies->
Fixed Lighting->
Modders Shoppe->

View All Products ->

All Products sorted by Categories ->

All Products sorted by Manufacturers ->
Use keywords to find the product you are looking for.
Specials more
Aleph 19 Head Kit-Natural
Aleph 19 Head Kit-Natural
 $49.00  $39.00 
Cyan Lambertian (HD)Star LXHL-ME1D Bin Q4JC **lower price
Cyan Lambertian (HD)Star LXHL-ME1D Bin Q4JC **lower price
 $6.50  $5.53 
McGizmo Titanium Clip 45mm
McGizmo Titanium Clip 45mm
 $15.50  $12.40 
Firefly CR2 power pack (seconds)
Firefly CR2 power pack (seconds)
 $27.00  $21.60 
MJ Cutdown High-power 5mm LED (original)
MJ Cutdown High-power 5mm LED (original)
 $4.50  $4.05 
Perfect XR19 Cree Heatsink - C
Perfect XR19 Cree Heatsink - C
 $19.00  $15.20 

PXR C + 4 Cree XR Emitter (P4) Combo
 $60.00  $48.00 

Camless M2 Light Orange Peel (LOP) Reflector
 $28.00  $22.40 
McTC Tailcap Natural
McTC Tailcap Natural
 $20.00  $16.00 

**M2 Camless Reflectors Info Page
 $0.00  $0.00 
Control Scan
Increase Sales with Verified Secure Seal from Control Scan!

GDuP Boost/Buck Converter HIGH output(3-level driver) 20% off

 $40.00 - $42.00 


GDuP Boost/Buck Converter HIGH output(3-level driver) 20% off

GDuP is a Microprocessor based fully-regulated boost/buck converter.  This is the high output version GDuP which has a resistor change giving it a broader range. 10mA-1200mA

The GDuP is based on the GD driver and is a true buck/boost converter. It will run from 1.8V to 5V safely. So, yes to two cell Alkaline, NiMH or even three cell Alkaline/NiMH.   Single 123, lithium battery.

Capable of stepping through three levels of brightness.

Default Levels are set at 20mA, 180mA and 1200mA

Click through the 3 levels and release after the blip to set.

The GDuP turns your single stage light into a three stage clicky or twisty.

Has the capability of retaining your last entered state.

Comes with bare anode contact board and one two pin connector. (only the GND connector pin mates with the anode board)

Board bare pcb thickness: ~0.9mm

Note:  If the GDuP converter is custom programmed and is successful, it is not tested again.

The GDuP has self calibration mode.


If you want it functionally tested it will cost $14.00 for each converter because wires need to be added and test performed. 



Tallest component top side: 3mm

Tallest component bottomside: 1mm

Total thickness ~4.9mm (0.193")

Board diameter: 0.55" (14mm)

The board runs best when used in a single cell application (CR123, RCR123 or 2,3 alkaline batteries).

Do not use this board in any two 123 cell configurations as this will fry the components on the board.

Board has components on both sides (bottomside not shown).

Extreme care must be taken when soldering this board to other components as too much heat and components will fall off either the top side or bottomside depending on which way gravity is pulling.

Custom versions of the UI can be made. Inquire for more info.

 See CPF thread here for more info.

NEW:  Change the 3 levels by choosing the yes option and typing in the desired levels in mA: ie.  50 200 1000

Range is 10mA -1200mA (GDuP High Output version)

Make sure you are logged in for your options to show  up on the order.

We tested this.  If you go to check out and you have not put in your name, address etc the options are not retained.

Please re-input your item and options.  The options will show up on your order as you go through check out.


How GDuP Auto-cal works:

When you turn the light on it will determine in 1 second if the current level is within specifications.  If it is not within specifications it will blip quickly once a 1 second.   This is the indicator it not calibrated.  It will automatically start a re-cal procedure and if successful ( a few seconds to many seconds later) it will blip quickly twice.  Once it blips twice it signifies it cal'd correctly and stored it away.

You can now cycle to the next level and wait to see if it auto-cals or not. You need to do this once and it will do this periodically with LED aging.

But, it's automatic.  Just use the light.  It should be correct after a few usages.

The full description is on the GDuP thread on CPF.

Available Options:
Change levels on GDuP:
Function Test:
Write in levels:


GDuP Boost/Buck Converter HIGH output(3-level driver) 20% off GDuP Boost/Buck Converter HIGH output(3-level driver) 20% off GDuP Boost/Buck Converter HIGH output(3-level driver) 20% off

Mfg Info

Manufacturer Info
Other products

Extra Info

There are currently no product reviews
Write a review on this product!

Extra Info
This product was added to our catalog on Wednesday 19 May, 2010.
Notify me of updates to GDuP Boost/Buck Converter HIGH output(3-level driver) 20% off
Tell someone you know about this product.

Quantity Price Chart
Base $42.00
2 - 10 $42.00
11 - 20 $41.00
21 - 30 $40.00
31 - 40 $40.00
41 - 50 $40.00
51 - 60 $40.00
61 - 70 $40.00
71 - Above $40.00
Add to Wish List
 $40.00 - $42.00  Quantity:     
Customers who bought this product also purchased
Contact Us->
Information Pages
Shopping Cart more
0 items
Your Account
Your Email Address
Your Password
Best Sellers
01.Fraen LP
02.EP O-Ring 18
03.Sandwich Retaining Oring #12
04.McE2S Rubber Boot Cap for E-series/Aleph tailcap
05.Retaining ring
06.O-ring-FF Better Fit 15
07.Arc Threaded Ring (limit 2 per person)
08.Titanium Bezel Ring (PD, A2, A19, HDS)
09.EP O-ring 19 for Aleph 2, Aleph 19 and PD head
10.O-Ring for FireflyII Bezel

Copyright © 2024 Chain Reaction Ecommerce, Inc. Powered by CRE Loaded
Using CRE Loaded PCI B2B v6.4.1